SMiLer is the strong brand enterprise of metallized film capacitors integrating R&D, production and sales.The main products: motor capacitor,capacitor manufacturer,fan capacitor.

Capacitor detection techniques to share

by:SMiLer     2021-02-04
Capacitor detection method mainly divided into three broad categories: detection variable capacitor, electrolytic capacitor, fixed capacitor detection. 1 turn with your hand lightly in the variable capacitor testing A rotating shaft, should feel very smooth, should not feel sometimes loose tight even have card lag phenomenon. Will be carried forward, backward, up, down, left and right when driving in all directions, such as a shaft should not have loose phenomenon. B with one hand twisted axis, and the other only the outside part of the handle gently touch this little group, should not feel any loose phenomenon. Axis and poor contact between the variable capacitor, is can't continue to use. C puts multimeter R&TImes; 10 k block, it is a hand to connect two pens and variable capacitor dynamic piece and piece of terminal, the other will slowly rotating shaft turn a few back and forth, multimeter pointer should place in infinity. In the process of the swirl shaft, if the pointer points to zero, sometimes short circuit between moving and fixed pills are point; If a certain Angle, the multimeter reading for infinity but not appear a certain value, that variable between the rotor plate with fixed leakage phenomenon. 2 fixed capacitor detection A 10 pf the following small capacitance for fixed capacitor capacity is too small, under 10 pf with A multimeter to measure, only qualitative to check whether there is leakage, its internal short circuit or breakdown phenomenon. When measuring, can choose multimeter R&TImes; 10 k block, two pens and arbitrary by capacitance respectively two pins, resistance should be infinite. If the measured resistance ( A pointer to the right) Is zero, then illustrate capacitor leakage internal breakdown or damage. 10 pf ~ 0 B detection. 01μ F the fixed capacitor charging phenomenon, and then judge the good or bad. Multimeter choose R&TImes; 1 k. Two triode & beta; Values are more than 100, and through the current can choose 3 dg6 models of silicon triode pipe etc. Multimeter of red and black pens and respectively with multiple tube of the emitter and the collector e c. Due to the amplification effect of compound triode, the measured capacitance charging and discharging process of amplification, the multimeter pointer swing amplitude increase, thus convenient for observation. Is that should be paid attention to in test operation, especially in the smaller capacity of capacitance measurement, repeatedly measured capacitance pin switch contact with A and B two points, can clearly see the motion of the pointer multimeter. C for 0. 01μ F the fixed capacitor, multimeter R&TImes are available; 10 k block capacitor test failures directly charging process and presence of internal short circuit or leakage, and according to the range of a pointer to the right size to estimate the capacity of capacitor. 3 electrolytic capacitor detection because the capacity of electrolytic capacitor is A fixed capacity is much bigger, so the measurement, should according to different capacity to choose the appropriate range. According to experience, usually, 1 ~ 47 & mu; F the capacitance between, usable R× 1 k block measurement, or more than 47 & mu; F capacitance R× available; 100 block measurement. B the multimeter red pens and negative, black pens and meet positive, at the moment just contact, multimeter pointer deflection is larger partial degrees to the right ( For the same electric block, the bigger the capacity, the greater the swing) , then gradually turning to the left until the stop at a particular location. At this time of the resistance value is positive leakage resistance of electrolytic capacitors, this value is slightly bigger than the reverse leakage resistance. Practical experience shows that the electrolytic capacitor leakage resistance should be in the hundreds of k&Omega commonly; Above, otherwise, will not work properly. If during the test, the forward and reverse the phenomenon of no charge, whose hands, which shows capacity disappear or internal circuit; If the measured value is small or zero, capacitor leakage is big or has broken down, cannot be used again. C for positive and negative sign of unknown electrolytic capacitor, can use the method of measurement of leakage resistance. The arbitrary measure leakage resistance, first remember its size, and then exchange pens and a resistance is measured. Two measurement of resistance that is a big positive connection, the black pens and pick up the positive, red pens and pick up is negative. D use multimeter electric block, using positive and reverse charge for electrolytic capacitor method, according to the size of the oscillation amplitude to the right hand side, can estimate the capacity of electrolytic capacitors.
SMILer Electornic Industrial Co., Ltd. supports their market leadership with savvy marketing skills to create an prime brand.
SMILer Electornic Industrial Co., Ltd. also maintains a friendly, fair, and creative work environment, which respects diversity, new ideas, and hard work.
Individuals with varied technical skills use ac motor capacitor in a wide range of applications.
SMILer Electornic Industrial Co., Ltd. will do this by managing our business with integrity and the highest ethical standards, while acting in a socially responsible manner with particular emphasis on the well-being of our teammates and the communities we serve.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...
We will get back to you ASAP